New Bern, NC Plumbing & HVAC Services
Trusted Heating, Cooling, and Plumbing Solutions for New Bern Homeowners
Since 1974, Jackson & Sons has been the trusted name for heating and air conditioning in New Bern. From fast AC repairs to full system replacements, our experienced technicians deliver high-quality solutions with a personal, family-oriented approach.
We are proud to expand our services to include full residential plumbing. Whether you are dealing with a leaking pipe, a clogged drain, or need a new water heater installed, you can now rely on the same team that New Bern homeowners trust for HVAC.
Our goal is simple: to provide fast, reliable service that keeps your home comfortable and functioning year-round.
If you are looking for reliable HVAC or plumbing solutions in Craven County, we are just a call (980) 223-0791 or click away.

Keep Cool All Summer with Expert AC Services
Our air conditioning services are designed to keep your home comfortable through New Bernās hot and humid summers. Whether your system needs a quick fix or a full replacement, we have the tools and training to get it done right.
AC Repair When You Need It Most
- Diagnose and fix warm air, short cycling, or poor airflow
- Address electrical or refrigerant issues causing system failure
- Service all major brands with fully stocked trucks for faster repairs
Energy-Efficient AC Installation
- Evaluate your home size, layout, and comfort needs
- Install energy-efficient central AC systems or heat pumps
- Properly size and balance airflow for long-term system performance
Stay Warm and Worry-Free with Reliable Heating Solutions
When temperatures drop, you need a heating system that works reliably. We provide repair, replacement, and maintenance services for furnaces and heat pumps to keep your home warm and energy-efficient through the winter.
Furnace and Heat Pump Repairs
- Troubleshoot uneven heating, pilot light issues, or strange noises
- Repair heat pumps, gas furnaces, and hybrid systems
- Restore consistent comfort and safe operation
New Heating System Installation
- Remove outdated or undersized systems
- Install high-efficiency furnaces and dual-fuel systems
- Help you select the right system for your home and energy goals
HVAC Maintenance
- Replace Filter / Clean If Permanent
- Disassemble Unit
- Clean Evaporator and Condenser Coils
- Remove All Leaves and Debris
- Tighten All Electrical Connections
- Measure Amp Draws on compressor, Motors and Heat Strips
- Inspect Outdoor Fan Blade
- Clean and Adjust Blower Wheel if Needed
- Clean and Inspect Flow of Condensate Drain
- Inspect and Test Defrost Cycle
- Inspect Crank Case Heater
- Test Capacitors
- Reassemble Unit, Replace Any Missing or Rusted Screws
- Wash Unit and Apply Protective Coating
- Monitor and Record Delta T
- Inspect Duct System
- Monitor Air Flow
- Inspect Thermostat and Reset to Customer Desire Settings
- Cycle System to Ensure Proper Operation
Restore Airflow and Efficiency with Ductwork Services
Professional Duct Repairs
Damaged or leaking ductwork can lead to hot and cold spots, reduced airflow, and increased energy bills. Our team identifies problem areas using pressure testing and thermal imaging, then seals, insulates, or repairs duct sections to restore performance and indoor comfort.
Complete Duct Replacement
If your ducts are undersized, poorly installed, or beyond repair, we can design and install a new duct system that supports your HVAC equipment and improves air distribution throughout your home. We follow best practices for airflow balance and energy efficiency.
Plumbing Solutions That Get the Job Done Right in New Bern
We bring the same level of professionalism and care to our plumbing services as we do to HVAC. Whether it is a small leak or a major backup, our licensed plumbers are ready with fast, effective solutions for your New Bern home.
Fix Whatās Leaking with Dependable Plumbing Repairs
Leaky fixtures and damaged pipes can waste water and drive up your utility bill. We handle a wide range of plumbing issues with solutions that last.
- Fix leaking faucets, running toilets, and burst pipes
- Repair water pressure issues and faulty shut-off valves
- Provide fast diagnosis and long-lasting repair options
Clear the Way with Drain and Sewer Services
Clogged drains can lead to water damage, foul odors, and recurring plumbing problems. Our team uses professional-grade equipment to clear and restore flow.
- Clear clogs in kitchen sinks, bathtubs, showers, and toilets
- Remove buildup, grease, and debris from interior and exterior lines
- Prevent backups and recurring drain problems with professional tools
Count on Us for Hot Water Help
A dependable water heater is essential to your daily routine. When hot water runs out or your system shows signs of trouble, we are here to restore comfort.
- Diagnose no hot water, rust-colored water, or strange noises
- Repair or replace tank and tankless water heater systems
- Install high-efficiency models sized for your householdās usage
Fixture Replacements For Your Home
Outdated or corroded fixtures not only affect function, they can impact your water usage and homeās appearance. We help modernize and improve performance.
- Upgrade faucets, toilets, and showerheads for better performance
- Replace corroded or leaking plumbing connections
- Improve water efficiency and refresh your homeās appearance
Emergency Plumbing When You Need It Now
Plumbing emergencies canāt wait. Whether your home is flooding from a burst pipe or your sewer line has backed up, our team responds quickly to protect your home and restore service during our business hours.
- Immediate help for pipe bursts, severe leaks, or flooding
- Fast response to water heater failure or sewer backups
- Restore safety and prevent further water damage
Why New Bern Homeowners Choose Jackson & Sons
Jackson & Sons has been a trusted name in heating and cooling for New Bern homeowners since 1974. For over 50 years, weāve delivered expert HVAC repairs, replacements, and maintenance with the kind of care only a family-oriented company can offer.Ā
Now, weāre proud to bring that same level of professionalism and reliability to your plumbing system. While plumbing is a newer service for us, itās backed by the same values, training, and customer-first mindset that have made our HVAC team one of the highest rated in Eastern North Carolina.
When you choose Jackson & Sons, you can expect:
- Licensed, background-checked HVAC and plumbing professionals
- Fast, responsive service with same-day availability whenever possible
- Honest pricing and clear communication
- Thousands of 5-star reviews from satisfied customers
- A team that truly cares about the comfort and safety of your home
When you need us, weāll be there ā with reliable service you can count on.
Call (980) 223-0791 or contact us online to schedule HVAC or plumbing service in New Bern today. We look forward to earning your trust and making your home more comfortable.
Recent Jobs and Reviews in New Bern, NC
New Bern, NC at a glance
Jackson & Sons has completed 25 jobs in New Bern, NC in September 2024.
The most recent job was on September 19, 2024.
Jackson & Sons completed its first job in New Bern, NC in September 2016.
Our Local Reviews by City
- Albertson, NC (17)
- Ayden, NC (26)
- Bailey, NC (9)
- Benson, NC (14)
- Beulaville, NC (21)
- Black Creek, NC (3)
- Brogden, NC (163)
- Calypso, NC (5)
- Chinquapin, NC (3)
- Clayton, NC (170)
- Clinton, NC (80)
- Cove City, NC (4)
- Deep Run, NC (32)
- Dover, NC (2)
- Dudley, NC (121)
- Dunn, NC (16)
- Elm City, NC (5)
- Erwin, NC (1)
- Faison, NC (40)
- Farmville, NC (30)
- Four Oaks, NC (69)
- Fremont, NC (148)
- Garner, NC (15)
- Goldsboro, NC (4285)
- Grantham, NC (2)
- Greenville, NC (175)
- Grifton, NC (14)
- Hookerton, NC (14)
- Jason, NC (1)
- Kenansville, NC (18)
- Kenly, NC (79)
- Kinston, NC (235)
- La Grange, NC (316)
- Lillington, NC (4)
- Lucama, NC (4)
- Magnolia, NC (4)
- Mar-Mac, NC (22)
- Micro, NC (2)
- Middlesex, NC (2)
- Mount Olive, NC (195)
- Nashville, NC (15)
- New Bern, NC (206)
- Newton Grove, NC (40)
- North Clinton, NC (1)
- Pikeville, NC (414)
- Pine Level, NC (5)
- Pink Hill, NC (27)
- Plain View, NC (1)
- Princeton, NC (156)
- Richlands, NC (3)
- Rocky Mount, NC (63)
- Rose Hill, NC (2)
- Roseboro, NC (6)
- Selma, NC (90)
- Seven Springs, NC (103)
- Sims, NC (2)
- Smithfield, NC (149)
- Snow Hill, NC (127)
- Stantonsburg, NC (30)
- Tarboro, NC (8)
- Teachey, NC (1)
- Turkey, NC (6)
- Vanceboro, NC (10)
- Wallace, NC (5)
- Walnut Creek, NC (45)
- Walstonburg, NC (9)
- Warsaw, NC (33)
- Wendell, NC (10)
- Willow Spring, NC (2)
- Wilson, NC (50)
- Wilson Mills, NC (1)
- Winterville, NC (94)
- Zebulon, NC (3)
Job Locations and Reviews
Tech found condensation on supply plenum insulation with a positive flow zone system. Tech found a few install problems that can lead to this. Tech found dampers opening and closing properly, but found bypass damper opening half way. A bypass should not open more than 1/4 to prevent too much supply air entering the return. This will cause a low supply temp which can cause sweating. This also indicates the supply trunks are not capable of holding all the airflow alone. Trunk line is 12 inches for upstairs and 14 inches for downstairs. 16 inches is what should be used for a 3.5 ton zone system. Tech also found a positive flow system with a deep trap and no vent before the trap. Tech shut blower off and found water drainage better indicating the blower is pushing water away from the drain exit. Tech also found no primary float switch installed so unit will only shut off if secondary pan is full. Customer stated secondary pan has been replaced due to corrosion indicating an ongo
Tech found condensation on supply plenum insulation with a positive flow zone system. Tech found a few install problems that can lead to this. Tech found dampers opening and closing properly, but found bypass damper opening half way. A bypass should not open more than 1/4 to prevent too much supply air entering the return. This will cause a low supply temp which can cause sweating. This also indicates the supply trunks are not capable of holding all the airflow alone. Trunk line is 12 inches for upstairs and 14 inches for downstairs. 16 inches is what should be used for a 3.5 ton zone system. Tech also found a positive flow system with a deep trap and no vent before the trap. Tech shut blower off and found water drainage better indicating the blower is pushing water away from the drain exit. Tech also found no primary float switch installed so unit will only shut off if secondary pan is full. Customer stated secondary pan has been replaced due to corrosion indicating an ongo
Tech found condensation on supply plenum insulation with a positive flow zone system. Tech found a few install problems that can lead to this. Tech found dampers opening and closing properly, but found bypass damper opening half way. A bypass should not open more than 1/4 to prevent too much supply air entering the return. This will cause a low supply temp which can cause sweating. This also indicates the supply trunks are not capable of holding all the airflow alone. Trunk line is 12 inches for upstairs and 14 inches for downstairs. 16 inches is what should be used for a 3.5 ton zone system. Tech also found a positive flow system with a deep trap and no vent before the trap. Tech shut blower off and found water drainage better indicating the blower is pushing water away from the drain exit. Tech also found no primary float switch installed so unit will only shut off if secondary pan is full. Customer stated secondary pan has been replaced due to corrosion indicating an ongo
Tech found condensation on supply plenum insulation with a positive flow zone system. Tech found a few install problems that can lead to this. Tech found dampers opening and closing properly, but found bypass damper opening half way. A bypass should not open more than 1/4 to prevent too much supply air entering the return. This will cause a low supply temp which can cause sweating. This also indicates the supply trunks are not capable of holding all the airflow alone. Trunk line is 12 inches for upstairs and 14 inches for downstairs. 16 inches is what should be used for a 3.5 ton zone system. Tech also found a positive flow system with a deep trap and no vent before the trap. Tech shut blower off and found water drainage better indicating the blower is pushing water away from the drain exit. Tech also found no primary float switch installed so unit will only shut off if secondary pan is full. Customer stated secondary pan has been replaced due to corrosion indicating an ongo
Tech found condensation on supply plenum insulation with a positive flow zone system. Tech found a few install problems that can lead to this. Tech found dampers opening and closing properly, but found bypass damper opening half way. A bypass should not open more than 1/4 to prevent too much supply air entering the return. This will cause a low supply temp which can cause sweating. This also indicates the supply trunks are not capable of holding all the airflow alone. Trunk line is 12 inches for upstairs and 14 inches for downstairs. 16 inches is what should be used for a 3.5 ton zone system. Tech also found a positive flow system with a deep trap and no vent before the trap. Tech shut blower off and found water drainage better indicating the blower is pushing water away from the drain exit. Tech also found no primary float switch installed so unit will only shut off if secondary pan is full. Customer stated secondary pan has been replaced due to corrosion indicating an ongo
Tech found condensation on supply plenum insulation with a positive flow zone system. Tech found a few install problems that can lead to this. Tech found dampers opening and closing properly, but found bypass damper opening half way. A bypass should not open more than 1/4 to prevent too much supply air entering the return. This will cause a low supply temp which can cause sweating. This also indicates the supply trunks are not capable of holding all the airflow alone. Trunk line is 12 inches for upstairs and 14 inches for downstairs. 16 inches is what should be used for a 3.5 ton zone system. Tech also found a positive flow system with a deep trap and no vent before the trap. Tech shut blower off and found water drainage better indicating the blower is pushing water away from the drain exit. Tech also found no primary float switch installed so unit will only shut off if secondary pan is full. Customer stated secondary pan has been replaced due to corrosion indicating an ongo
Tech found condensation on supply plenum insulation with a positive flow zone system. Tech found a few install problems that can lead to this. Tech found dampers opening and closing properly, but found bypass damper opening half way. A bypass should not open more than 1/4 to prevent too much supply air entering the return. This will cause a low supply temp which can cause sweating. This also indicates the supply trunks are not capable of holding all the airflow alone. Trunk line is 12 inches for upstairs and 14 inches for downstairs. 16 inches is what should be used for a 3.5 ton zone system. Tech also found a positive flow system with a deep trap and no vent before the trap. Tech shut blower off and found water drainage better indicating the blower is pushing water away from the drain exit. Tech also found no primary float switch installed so unit will only shut off if secondary pan is full. Customer stated secondary pan has been replaced due to corrosion indicating an ongo
Tech found condensation on supply plenum insulation with a positive flow zone system. Tech found a few install problems that can lead to this. Tech found dampers opening and closing properly, but found bypass damper opening half way. A bypass should not open more than 1/4 to prevent too much supply air entering the return. This will cause a low supply temp which can cause sweating. This also indicates the supply trunks are not capable of holding all the airflow alone. Trunk line is 12 inches for upstairs and 14 inches for downstairs. 16 inches is what should be used for a 3.5 ton zone system. Tech also found a positive flow system with a deep trap and no vent before the trap. Tech shut blower off and found water drainage better indicating the blower is pushing water away from the drain exit. Tech also found no primary float switch installed so unit will only shut off if secondary pan is full. Customer stated secondary pan has been replaced due to corrosion indicating an ongo
Tech performed service on trane split system. Recommend (1) 20x30 media filter and surge protector. Customer is interested and said will do next maintenance visit. Customer renewed maintenance plan. Found no other challenges at todays visit.
Tech performed service on bryant split system. Recommend plasma air. Customer declined but said maybe in future. Customer renewed maintenance plan Found no other challenges at todays visit.
CMA Proposal
Tech performed esa on one system, Tech recommended adding attic tent to prevent attic temperatures from getting in home and conflicting with thermostat. tech found no other issues or have any other recommendations at this time. System is back on and operating properly at this time. Customers use their own filters.
Tech found 3 in shot burners that had rusted out causing improper flame and gas path. Tech recommended replacing. Tech returned and replaced 3 insult burners. System is back on and operating properly at this time.
Found system on low pressure lockout void of refrigerant. Located leak at location of previous repair. Repaired leak, and passed both pressure/vacuum tests. Re-charged to factory specs of 6.6lbs of R410a. System back up and cooling. Service warranty.
Tech performed esa on one system, Tech recommended adding eztrap and float switch to system to enhance drain performance and prevent overflow into pan and potential ceiling damage. no other issues were found at todays visit. System is back on and operating properly at this time. Tenants supplied personal filters.
Tech performed tune up on one system, Tech recommended installing eztrap and float switch to help prevent clogged drains and potential overflow causing damage to ceiling. tech found no other issues with system at todays visit. System is back on and operating properly at this time. Customer signed up for one system MPA.
Performed CMA on (2) split heat pump systems. All (4) returns were missing filters. Installed (4) 20x20x1 filters into returns. Older Ruud air handler does not have proper slope from either drain. Condensate pump installation has been previously recommended to resolve this issue. Outlet would need to be installed in drop ceiling. Spoke with building tenant. He will have landlord reach out to have repairs priced.
Replaced hot and cold cartridge on sink to stop dripping also replaced another cartridge on second sink.
Upon arrival tech was shown where there was water damage on ceiling coming from the system. Tech found auxiliary drain pan had 1/2ā of standing water in it. Removed water using transfer pump. Tech noticed that the corners on pan were not folded inside itself but had a rivet and caulk sealing. Suspects leak is cause from caulk eroding away over the years. Pan also does not have a safety switch installed. Tech recommends replacing with a new pan and installing switch but homeowners decided to hold off for now. Took pictures of ceiling where damage was in entry way and closet.
(System #5) found failed dual run capacitor. Replaced capacitor/added AC renew. System back up and cooling. Mrs. Posta approved todays invoice.
Went over customer issues with Bryce
Found auxiliary pan full causing float switch to trip due to clogged drain line. Cleared drain line and removed excess water. Cycled system from both zones with no further challenges. Invested in ESA (1) system. Schedule 1st visit. Mrs. Margaret approved via phone. Adam will be contacting regarding payment.
Upon arrival tech found condenser was in hard lockout, tech reset and inspected system and found no challenges system is run with correct amp draws, pressures and delta t. Tech was unable to pinpoint and challenges at todayās visit system is now back up and cooling.
Replace moen cartridge 1222 and moen handle fasteners Also replace pop up drain
Unit 1A- has 30 amp 3 pole breaker in main panel. Installed 5 kw heat strips. Marked heat strips on data tag. Has 208 volt to system. Verified transformer tap is 208. System operating properly.

