Smithfield, NC Plumbing & HVAC Services
Air Conditioning Services That Keep You Cool in Smithfield
Our technicians are trained to handle all types of cooling issues, whether you need a quick repair or a completely new system.
AC Repair
- Diagnose issues like warm air, low airflow, or system failure
- Fix electrical faults, frozen coils, or refrigerant problems
- Fast, same-day service available whenever possible
AC Installation
- Install energy-efficient central air or heat pump systems
- Proper sizing and airflow balancing for optimal performance
- Full walk-through and system training included
Heating Services to Keep You Comfortable
We help you stay warm with reliable service for furnaces and heat pumps throughout the colder months.
Heating Repair
- Identify common problems like no heat, uneven temps, or system cycling
- Service for all brands of furnaces and heat pumps
New Heating Installation
- Replace aging or inefficient systems with modern, energy-saving options
- Expert guidance to find the best solution for your home
Heating & Cooling Maintenance
- Replace Filter / Clean If Permanent
- Disassemble Unit
- Clean Evaporator and Condenser Coils
- Remove All Leaves and Debris
- Tighten All Electrical Connections
- Measure Amp Draws on Compressor, Motors and Heat Strips
- Inspect Outdoor Fan Blade
- Clean and Adjust Blower Wheel if Needed
- Clean and Inspect Flow of Condensate Drain
- Inspect and Test Defrost Cycle
- Inspect Crank Case Heater
- Test Capacitors
- Reassemble Unit, Replace Any Missing or Rusted Screws
- Wash Unit and Apply Protective Coating
- Monitor and Record Delta T
- Inspect Duct System
- Monitor Air Flow
- Inspect Thermostat and Reset to Customer Desire Settings
- Cycle System to Ensure Proper Operation
Full-Service Furnace and Heat Pump Solutions in Smithfield, NC
When winter temperatures drop in Smithfield, your home deserves a heating system you can rely on. At Jackson & Sons, we provide complete furnace and heat pump services tailored to your homeās needs. Whether youāre upgrading an aging system, handling unexpected repairs, or preparing for the season with routine maintenance, our licensed technicians have you covered.
- Install energy-efficient furnaces and heat pumps for consistent winter comfort
- Repair issues like uneven heating, strange smells, or short cycling
- Perform seasonal maintenance to keep your system running safely and efficiently
- Provide expert sizing and system recommendations for new homes or replacements
Stay warm all season long with dependable heating solutions backed by over 50 years of local service.
Indoor Air Quality Products & Services
Clean, healthy indoor air is essential for year-round comfort in Smithfield. At Jackson & Sons, we offer professional indoor air quality services designed to help your family breathe easier. Whether you are battling humidity, allergies, or poor airflow, we can recommend the right solution for your home.
Our indoor air quality services include:
- Installing whole-home air purifiers to remove dust, allergens, and airborne pollutants
- Adding dehumidifiers to control excess moisture and prevent mold growth
- Recommending and installing energy-recovery ventilators for fresh air circulation
- Upgrading HVAC filters and optimizing air handler settings for cleaner airflow
- Conducting air quality assessments to tailor solutions to your homeās needs
Let us help you create a safer, healthier indoor environment in your Smithfield home.
Ductwork Services That Improve Airflow and Comfort
Leaky or poorly designed ductwork can drive up energy bills and leave parts of your home too hot or too cold. At Jackson & Sons, we offer professional ductwork services for homeowners in Smithfield to help restore comfort, improve system performance, and lower utility costs.
- Duct Repair
- Seal and reinforce damaged or disconnected ducts
- Improve airflow to every room in your home
- Duct Replacement
- Remove and replace undersized or failing ductwork
- Install properly insulated, balanced systems for peak efficiency
Plumbing Services for Every Room in the House
Now serving Smithfield with full-service plumbing, Jackson & Sons brings the same trusted care and professionalism our HVAC customers have counted on for decades. Whether youāre dealing with a slow drain, a leaking pipe, or an unexpected plumbing emergency, our licensed plumbers are ready to respond quickly with reliable, long-lasting solutions.
We proudly serve homes throughout Smithfield and nearby Johnston County communities with expert plumbing repairs, installations, and maintenance for kitchens, bathrooms, laundry rooms, and beyond.
Reliable Plumbing Repairs
- Repair leaking faucets, burst pipes, and running toilets
- Fix water pressure issues and damaged valves
- Quick diagnosis with honest recommendations
Drain and Sewer Services
- Clear tough clogs in kitchens, bathrooms, and main lines
- Use professional-grade equipment to remove buildup and debris
- Prevent future blockages and restore normal flow
Water Heater Services
- Repair tank and tankless water heaters
- Resolve no hot water, pilot light issues, or leaking units
- Install efficient models to match your household size and needs
Fixture Upgrades
- Replace outdated faucets, toilets, and showerheads
- Improve water flow, efficiency, and appearance
Emergency Plumbing Help
- Respond to burst pipes, major leaks, and backups
- Stop damage and restore service fast with same-day availability
Why Smithfield Homeowners Trust Jackson & Sons
Weāve served the Smithfield community for generations with reliable HVAC service built on family values, professional workmanship, and local pride. With the addition of our plumbing division, weāre making it even easier to get expert care for your entire home.
- Trusted HVAC provider since 1974
- Now offering licensed plumbing services in Smithfield, NC
- Family-oriented and operated with a focus on quality and integrity
- Same-day service availability whenever possible
- Backed by thousands of 5-star reviewsĀ
When You Need Us, Weāll Be There ā For HVAC and Plumbing in Smithfield, NC
Whether you need furnace repair, AC replacement, or urgent help with a plumbing issue, Jackson & Sons is here with fast, reliable service in Smithfield and nearby communities.
Call (980) 223-0791 or contact us online to schedule your HVAC or plumbing service today. When you need us, weāll be there ā with the comfort and care your home deserves.
Jackson & Sons has completed 25 jobs in Smithfield, NC in October 2024. The most recent job was on October 16, 2024. Jackson & Sons has completed 1 job in Smithfield, NC in the last 12 months. The first job there was in August 2016.Recent Jobs and Reviews in Smithfield, NC
Smithfield, NC at a glance
Our Local Reviews by City
Job Locations and Reviews
Upon arrival tech found thermostat blank, found pressure switch wire shorted against refrigerant line. Factory transformer was not wired with fuse therefore transformer failed. Tech replaced transformer and wired in 5 amp blade fuse. Repaired short and tested, system is back up and heating.
TECH PERFORMED CMA FULL SERVICE ON 1 PTAC SYSTEM. TECH LEAK TESTED CONDENSER AND EVAPORATOR COILS, THERE WAS NO LEAK FOUND. TECH CHECKED TEMPERATURE COMING OUT OF SYSTEM TO ENSURE PROPER COOLING. SYSTEM IS COOLING AND PERFORMING PROPERLY AT THIS TIME.
TECH PERFORMED CMA FULL SERVICE ON 1 PTAC SYSTEM. TECH LEAK SEARCHED EVAPORATOR AND CONDENSER COILS, THERE WERE NO LEAKS DETECTED. TECH WASHED FILTERS AND CHECK TEMPERATURE TO ASSURE PROPER COOLING. SYSTEM IS PERFORMING PROPERLY.
Tech found system immediately shutting off on low suction. Tech found filter drier outlet condensation. Tech checked temperature split on both sides of the filter drier and found a 50 degree difference indicating a severely clogged filter drier. With this severe filter drier clog, tech performed an acid test to see if moisture was clogging the filter drier. Tech found no acid but explained that there is a chance the fixed orifices at the evaporator coil are clogged, but filter drier would need to be replaced before further diagnosis. Tech sent estimate for repair.
Tech found system immediately shutting off on low suction. Tech found filter drier outlet condensation. Tech checked temperature split on both sides of the filter drier and found a 50 degree difference indicating a severely clogged filter drier. With this severe filter drier clog, tech performed an acid test to see if moisture was clogging the filter drier. Tech found no acid but explained that there is a chance the fixed orifices at the evaporator coil are clogged, but filter drier would need to be replaced before further diagnosis. Tech sent estimate for repair.
Tech found system immediately shutting off on low suction. Tech found filter drier outlet condensation. Tech checked temperature split on both sides of the filter drier and found a 50 degree difference indicating a severely clogged filter drier. With this severe filter drier clog, tech performed an acid test to see if moisture was clogging the filter drier. Tech found no acid but explained that there is a chance the fixed orifices at the evaporator coil are clogged, but filter drier would need to be replaced before further diagnosis. Tech sent estimate for repair.
Tech found system immediately shutting off on low suction. Tech found filter drier outlet condensation. Tech checked temperature split on both sides of the filter drier and found a 50 degree difference indicating a severely clogged filter drier. With this severe filter drier clog, tech performed an acid test to see if moisture was clogging the filter drier. Tech found no acid but explained that there is a chance the fixed orifices at the evaporator coil are clogged, but filter drier would need to be replaced before further diagnosis. Tech sent estimate for repair.
Tech found system immediately shutting off on low suction. Tech found filter drier outlet condensation. Tech checked temperature split on both sides of the filter drier and found a 50 degree difference indicating a severely clogged filter drier. With this severe filter drier clog, tech performed an acid test to see if moisture was clogging the filter drier. Tech found no acid but explained that there is a chance the fixed orifices at the evaporator coil are clogged, but filter drier would need to be replaced before further diagnosis. Tech sent estimate for repair.
Tech found system immediately shutting off on low suction. Tech found filter drier outlet condensation. Tech checked temperature split on both sides of the filter drier and found a 50 degree difference indicating a severely clogged filter drier. With this severe filter drier clog, tech performed an acid test to see if moisture was clogging the filter drier. Tech found no acid but explained that there is a chance the fixed orifices at the evaporator coil are clogged, but filter drier would need to be replaced before further diagnosis. Tech sent estimate for repair.
Tech found system immediately shutting off on low suction. Tech found filter drier outlet condensation. Tech checked temperature split on both sides of the filter drier and found a 50 degree difference indicating a severely clogged filter drier. With this severe filter drier clog, tech performed an acid test to see if moisture was clogging the filter drier. Tech found no acid but explained that there is a chance the fixed orifices at the evaporator coil are clogged, but filter drier would need to be replaced before further diagnosis. Tech sent estimate for repair.
Tech found system immediately shutting off on low suction. Tech found filter drier outlet condensation. Tech checked temperature split on both sides of the filter drier and found a 50 degree difference indicating a severely clogged filter drier. With this severe filter drier clog, tech performed an acid test to see if moisture was clogging the filter drier. Tech found no acid but explained that there is a chance the fixed orifices at the evaporator coil are clogged, but filter drier would need to be replaced before further diagnosis. Tech sent estimate for repair.
Tech found system immediately shutting off on low suction. Tech found filter drier outlet condensation. Tech checked temperature split on both sides of the filter drier and found a 50 degree difference indicating a severely clogged filter drier. With this severe filter drier clog, tech performed an acid test to see if moisture was clogging the filter drier. Tech found no acid but explained that there is a chance the fixed orifices at the evaporator coil are clogged, but filter drier would need to be replaced before further diagnosis. Tech sent estimate for repair.
TECH PERFORMED CMA FULL SERVICE ON 1 PTAC SYSTEM. TECH CHECKED THERMOSTAT FOR PROPER FUNCTIONING, THERMOSTAT IS FUNCTIONING PROPERLY. TECH LEAK TESTED EVAPORATOR AND CONDENSER COILS, THERE WERE NO LEAKS FOUND. TECH TOOK OUT FILTERS, WASHED FILTERS AND PUT THEM BACK IN PROPER PLACE. SYSTEM IS PERFORMING PROPERLY AT THIS TIME.
Tech found inducer wheel rusted off, tech replaced motor after approval system is now back heating properly at this time.
Tech performed PSA tune up on system. Tech found no challenges at this time.
Tech washed and serviced unit and found no challenges at this time. Tech recommended hardstart customer would like to wait.
Performed CMA Filter Change
Concern - customer notified the tech that the salon is always too cold when the air is on. After inspection it was determined that the supply register for the salon does not have a damper, whereas other supply vents in different rooms do. Customer requested pricing on having a damper installed in salon in order to adjust airflow. Estimate was built and attached to this job.
(400 Back wing unit) Found 3 pole contactor shorted. Replaced contactor and added AC renew after approval from Mike. System back up and cooling.
(Kitchen unit) System has been down for quite some time. Another company has looked at system but maintenance was unaware of what the issue is. System is not receiving line voltage. Found empty breaker breakout in main panel, and breaker in closest disconnect panel to unit is not wired. Maintenance is going to have electrician take a look.
Install Trane 3 Ton Package Heat Pump
With Plasma Air
With WiFi Programmable Thermostat
Tech Performed esa on one system. Evaporator coil is leaking and field supervisor has already been out. Tech reinforced customer of issues and spoke with her regarding replacement customer stated she has other projects going on run and will have to wait. System is on and operating at this time.
Tech performed esa on one system, tech performed leak search of coil per previous invoice but was unable to detect any leaks at this time, tech calibrated and checked leak detector to ensure that tool is operating properly and everything was working properly, tech leak searched for a second time and still did not detect any leaks, informed customer of condition and that it may have issues with leaks in near future. Tech did not find any operational issues at this time.
Tech performed esa on one system, Tech found that air handler has excessive amounts of bacteria growing inside unit. Tech recommended adding plasma to prevent issue from occurring and contaminating ducts and home. Tech also recommends installation of eztrap and float switch. tech found no other issues and system is back on and operating properly at this time.
Customer invested in a 3 ton Trane PHP
Consultation Code: ENG9V6ATY
- Customer informed tech that the system stopped working shortly before this visit, with no response from the system when thermostat calls for cooling. Customer advised that renovations have been an ongoing process in one of the rooms where a return vent is located.
- Tech found both media filters dirty upon arrival and observed blower motor not operating with compressor and condenser fan running.
- Confirmed 240V power and 24V input to the true variable speed motor with no response. Motor and module have failed and must be replaced for system to operate.
- Advised customer and provided non-warranty pricing for the repair and recommended a system replacement on account of the systemās age. Dispatched field supervisor to provide replacement quote and options.
Left power off at disconnect box to prevent further challenges.
- Customer informed tech that the system stopped working shortly before this visit, with no response from the system when thermostat calls for cooling. Customer advised that renovations have been an ongoing process in one of the rooms where a return vent is located.
- Tech found both media filters dirty upon arrival and observed blower motor not operating with compressor and condenser fan running.
- Confirmed 240V power and 24V input to the true variable speed motor with no response. Motor and module have failed and must be replaced for system to operate.
- Advised customer and provided non-warranty pricing for the repair and recommended a system replacement on account of the systemās age. Dispatched field supervisor to provide replacement quote and options.
Left power off at disconnect box to prevent further challenges.

