Smithfield, NC Plumbing & HVAC Services
Air Conditioning Services That Keep You Cool in Smithfield
Our technicians are trained to handle all types of cooling issues, whether you need a quick repair or a completely new system.
AC Repair
- Diagnose issues like warm air, low airflow, or system failure
- Fix electrical faults, frozen coils, or refrigerant problems
- Fast, same-day service available whenever possible
AC Installation
- Install energy-efficient central air or heat pump systems
- Proper sizing and airflow balancing for optimal performance
- Full walk-through and system training included
Heating Services to Keep You Comfortable
We help you stay warm with reliable service for furnaces and heat pumps throughout the colder months.
Heating Repair
- Identify common problems like no heat, uneven temps, or system cycling
- Service for all brands of furnaces and heat pumps
New Heating Installation
- Replace aging or inefficient systems with modern, energy-saving options
- Expert guidance to find the best solution for your home
Heating & Cooling Maintenance
- Replace Filter / Clean If Permanent
- Disassemble Unit
- Clean Evaporator and Condenser Coils
- Remove All Leaves and Debris
- Tighten All Electrical Connections
- Measure Amp Draws on Compressor, Motors and Heat Strips
- Inspect Outdoor Fan Blade
- Clean and Adjust Blower Wheel if Needed
- Clean and Inspect Flow of Condensate Drain
- Inspect and Test Defrost Cycle
- Inspect Crank Case Heater
- Test Capacitors
- Reassemble Unit, Replace Any Missing or Rusted Screws
- Wash Unit and Apply Protective Coating
- Monitor and Record Delta T
- Inspect Duct System
- Monitor Air Flow
- Inspect Thermostat and Reset to Customer Desire Settings
- Cycle System to Ensure Proper Operation
Full-Service Furnace and Heat Pump Solutions in Smithfield, NC
When winter temperatures drop in Smithfield, your home deserves a heating system you can rely on. At Jackson & Sons, we provide complete furnace and heat pump services tailored to your homeās needs. Whether youāre upgrading an aging system, handling unexpected repairs, or preparing for the season with routine maintenance, our licensed technicians have you covered.
- Install energy-efficient furnaces and heat pumps for consistent winter comfort
- Repair issues like uneven heating, strange smells, or short cycling
- Perform seasonal maintenance to keep your system running safely and efficiently
- Provide expert sizing and system recommendations for new homes or replacements
Stay warm all season long with dependable heating solutions backed by over 50 years of local service.
Indoor Air Quality Products & Services
Clean, healthy indoor air is essential for year-round comfort in Smithfield. At Jackson & Sons, we offer professional indoor air quality services designed to help your family breathe easier. Whether you are battling humidity, allergies, or poor airflow, we can recommend the right solution for your home.
Our indoor air quality services include:
- Installing whole-home air purifiers to remove dust, allergens, and airborne pollutants
- Adding dehumidifiers to control excess moisture and prevent mold growth
- Recommending and installing energy-recovery ventilators for fresh air circulation
- Upgrading HVAC filters and optimizing air handler settings for cleaner airflow
- Conducting air quality assessments to tailor solutions to your homeās needs
Let us help you create a safer, healthier indoor environment in your Smithfield home.
Ductwork Services That Improve Airflow and Comfort
Leaky or poorly designed ductwork can drive up energy bills and leave parts of your home too hot or too cold. At Jackson & Sons, we offer professional ductwork services for homeowners in Smithfield to help restore comfort, improve system performance, and lower utility costs.
- Duct Repair
- Seal and reinforce damaged or disconnected ducts
- Improve airflow to every room in your home
- Duct Replacement
- Remove and replace undersized or failing ductwork
- Install properly insulated, balanced systems for peak efficiency
Plumbing Services for Every Room in the House
Now serving Smithfield with full-service plumbing, Jackson & Sons brings the same trusted care and professionalism our HVAC customers have counted on for decades. Whether youāre dealing with a slow drain, a leaking pipe, or an unexpected plumbing emergency, our licensed plumbers are ready to respond quickly with reliable, long-lasting solutions.
We proudly serve homes throughout Smithfield and nearby Johnston County communities with expert plumbing repairs, installations, and maintenance for kitchens, bathrooms, laundry rooms, and beyond.
Reliable Plumbing Repairs
- Repair leaking faucets, burst pipes, and running toilets
- Fix water pressure issues and damaged valves
- Quick diagnosis with honest recommendations
Drain and Sewer Services
- Clear tough clogs in kitchens, bathrooms, and main lines
- Use professional-grade equipment to remove buildup and debris
- Prevent future blockages and restore normal flow
Water Heater Services
- Repair tank and tankless water heaters
- Resolve no hot water, pilot light issues, or leaking units
- Install efficient models to match your household size and needs
Fixture Upgrades
- Replace outdated faucets, toilets, and showerheads
- Improve water flow, efficiency, and appearance
Emergency Plumbing Help
- Respond to burst pipes, major leaks, and backups
- Stop damage and restore service fast with same-day availability
Why Smithfield Homeowners Trust Jackson & Sons
Weāve served the Smithfield community for generations with reliable HVAC service built on family values, professional workmanship, and local pride. With the addition of our plumbing division, weāre making it even easier to get expert care for your entire home.
- Trusted HVAC provider since 1974
- Now offering licensed plumbing services in Smithfield, NC
- Family-oriented and operated with a focus on quality and integrity
- Same-day service availability whenever possible
- Backed by thousands of 5-star reviewsĀ
When You Need Us, Weāll Be There ā For HVAC and Plumbing in Smithfield, NC
Whether you need furnace repair, AC replacement, or urgent help with a plumbing issue, Jackson & Sons is here with fast, reliable service in Smithfield and nearby communities.
Call (980) 223-0791 or contact us online to schedule your HVAC or plumbing service today. When you need us, weāll be there ā with the comfort and care your home deserves.
Jackson & Sons has completed 25 jobs in Smithfield, NC in August 2024. The most recent job was on August 16, 2024. Jackson & Sons has completed 1 job in Smithfield, NC in the last 12 months. The first job there was in August 2016.Recent Jobs and Reviews in Smithfield, NC
Smithfield, NC at a glance
Our Local Reviews by City
Job Locations and Reviews
Tech found blower motor not running with a call at g. Tech jumped out the board and found blower rocking back and forth. Tech found the blower shaft does not spin freely. This indicates the blower has failed, but since the blower was not running at all before indicates an issue with the variable speed board as well. Tech restarted system and jumped r to g and found the blower rocking back and forth with the board call indicating the board is sending the call but intermittently will drop the call. Blower board and motor would need to be replaced. Due to age and cost of repair, tech recommends replacing system. Unit is 16 years old. Field supervisor needs to be notified.
Tech found breaker tripping as soon as it gets reset. Tech found breaker making a loud noise and was getting hot. Breaker panel was in poor condition and tech suspected an issue with the breaker. Tech removed wires from breaker and found breaker still tripping with no load wires connected. Tech tried a different breaker and found breaker does not trip without load wires, but as soon as load wires are put into breaker, breaker trips again. Tech ohmed compressor and found 7 ohms to ground indicating a grounded compressor. Tech removed compressor plug and found breaker is not tripping. Tech recommends calling an electrician to inspect the electrical panel and suspects panel was the cause of the failed compressor. Tech recommends replacing unit due to age and condition as well as cost of repair. Field supervisor needs to be notified.
Tech found breaker tripping as soon as it gets reset. Tech found breaker making a loud noise and was getting hot. Breaker panel was in poor condition and tech suspected an issue with the breaker. Tech removed wires from breaker and found breaker still tripping with no load wires connected. Tech tried a different breaker and found breaker does not trip without load wires, but as soon as load wires are put into breaker, breaker trips again. Tech ohmed compressor and found 7 ohms to ground indicating a grounded compressor. Tech removed compressor plug and found breaker is not tripping. Tech recommends calling an electrician to inspect the electrical panel and suspects panel was the cause of the failed compressor. Tech recommends replacing unit due to age and condition as well as cost of repair. Field supervisor needs to be notified.
Tech found breaker tripping as soon as it gets reset. Tech found breaker making a loud noise and was getting hot. Breaker panel was in poor condition and tech suspected an issue with the breaker. Tech removed wires from breaker and found breaker still tripping with no load wires connected. Tech tried a different breaker and found breaker does not trip without load wires, but as soon as load wires are put into breaker, breaker trips again. Tech ohmed compressor and found 7 ohms to ground indicating a grounded compressor. Tech removed compressor plug and found breaker is not tripping. Tech recommends calling an electrician to inspect the electrical panel and suspects panel was the cause of the failed compressor. Tech recommends replacing unit due to age and condition as well as cost of repair. Field supervisor needs to be notified.
Tech found breaker tripping as soon as it gets reset. Tech found breaker making a loud noise and was getting hot. Breaker panel was in poor condition and tech suspected an issue with the breaker. Tech removed wires from breaker and found breaker still tripping with no load wires connected. Tech tried a different breaker and found breaker does not trip without load wires, but as soon as load wires are put into breaker, breaker trips again. Tech ohmed compressor and found 7 ohms to ground indicating a grounded compressor. Tech removed compressor plug and found breaker is not tripping. Tech recommends calling an electrician to inspect the electrical panel and suspects panel was the cause of the failed compressor. Tech recommends replacing unit due to age and condition as well as cost of repair. Field supervisor needs to be notified.
Tech found breaker tripping as soon as it gets reset. Tech found breaker making a loud noise and was getting hot. Breaker panel was in poor condition and tech suspected an issue with the breaker. Tech removed wires from breaker and found breaker still tripping with no load wires connected. Tech tried a different breaker and found breaker does not trip without load wires, but as soon as load wires are put into breaker, breaker trips again. Tech ohmed compressor and found 7 ohms to ground indicating a grounded compressor. Tech removed compressor plug and found breaker is not tripping. Tech recommends calling an electrician to inspect the electrical panel and suspects panel was the cause of the failed compressor. Tech recommends replacing unit due to age and condition as well as cost of repair. Field supervisor needs to be notified.
Tech found breaker tripping as soon as it gets reset. Tech found breaker making a loud noise and was getting hot. Breaker panel was in poor condition and tech suspected an issue with the breaker. Tech removed wires from breaker and found breaker still tripping with no load wires connected. Tech tried a different breaker and found breaker does not trip without load wires, but as soon as load wires are put into breaker, breaker trips again. Tech ohmed compressor and found 7 ohms to ground indicating a grounded compressor. Tech removed compressor plug and found breaker is not tripping. Tech recommends calling an electrician to inspect the electrical panel and suspects panel was the cause of the failed compressor. Tech recommends replacing unit due to age and condition as well as cost of repair. Field supervisor needs to be notified.
Tech found breaker tripping as soon as it gets reset. Tech found breaker making a loud noise and was getting hot. Breaker panel was in poor condition and tech suspected an issue with the breaker. Tech removed wires from breaker and found breaker still tripping with no load wires connected. Tech tried a different breaker and found breaker does not trip without load wires, but as soon as load wires are put into breaker, breaker trips again. Tech ohmed compressor and found 7 ohms to ground indicating a grounded compressor. Tech removed compressor plug and found breaker is not tripping. Tech recommends calling an electrician to inspect the electrical panel and suspects panel was the cause of the failed compressor. Tech recommends replacing unit due to age and condition as well as cost of repair. Field supervisor needs to be notified.
Tech found breaker tripping as soon as it gets reset. Tech found breaker making a loud noise and was getting hot. Breaker panel was in poor condition and tech suspected an issue with the breaker. Tech removed wires from breaker and found breaker still tripping with no load wires connected. Tech tried a different breaker and found breaker does not trip without load wires, but as soon as load wires are put into breaker, breaker trips again. Tech ohmed compressor and found 7 ohms to ground indicating a grounded compressor. Tech removed compressor plug and found breaker is not tripping. Tech recommends calling an electrician to inspect the electrical panel and suspects panel was the cause of the failed compressor. Tech recommends replacing unit due to age and condition as well as cost of repair. Field supervisor needs to be notified.
Tech found breaker tripping as soon as it gets reset. Tech found breaker making a loud noise and was getting hot. Breaker panel was in poor condition and tech suspected an issue with the breaker. Tech removed wires from breaker and found breaker still tripping with no load wires connected. Tech tried a different breaker and found breaker does not trip without load wires, but as soon as load wires are put into breaker, breaker trips again. Tech ohmed compressor and found 7 ohms to ground indicating a grounded compressor. Tech removed compressor plug and found breaker is not tripping. Tech recommends calling an electrician to inspect the electrical panel and suspects panel was the cause of the failed compressor. Tech recommends replacing unit due to age and condition as well as cost of repair. Field supervisor needs to be notified.
Upon arrival tech found compressor not running, compressor was in an overload. Cooled compressor and attempted to start. Compressor pulled locked rotor amps, attempted several more times to free compressor with no luck. Compressor is failed and will need to be replaced. Inform customer when possible of estimated repair date.
Performed CMA Full Service on 13 Rooftop Gas Package Units and 6 Split Heat Pump Systems.
Rooftop Units TRANE 2 and TRANE 3 (right side of building from road) are down. Power disconnected at panel. Per customer request, technician left these systems be.
Rooftop Units TRANE 7 (right side of building from road) and RTU 5 (left side of building from road) - both systems are only operational at half capacity. TRANE 7 - compressor 1 shorted to ground. RTU 5 - circuit 1 is at 0 psi. Customer aware of these challenges.
Rooftop Unit TRANE 4 (right side of building from road) - technician found transformer receiving 500v from line voltage, however, there was not a low voltage reading coming from the other side.
Split Systems -Outdoor fan motors on HP 4 and 5 are both reading above the designed amperage of the motor. Customer made aware of this. Estimates built, oem size is 1/4 1100rpm. Motor on estimate is as close as we have: 1/4 1075
No other challenges were present at this time. There
Tech washed and serviced unit and found no challenges at this time. System is back up and cooling tech recommended surge protector.
Tech washed and serviced units per service agreement, upon arrival tech could not get to upstairs air handler, would like to reschedule to get upstairs air handler serviced,tech serviced the two condensers and downstairs air handler, both systems are back up and running with a delta t of within spec. Tech found no challenges at todayās visit.
Tech washed and serviced units per service agreement, upon arrival tech could not get to upstairs air handler, would like to reschedule to get upstairs air handler serviced,tech serviced the two condensers and downstairs air handler, both systems are back up and running with a delta t of within spec. Tech found no challenges at todayās visit.
Tech washed and serviced units per service agreement, upon arrival tech could not get to upstairs air handler, would like to reschedule to get upstairs air handler serviced,tech serviced the two condensers and downstairs air handler, both systems are back up and running with a delta t of within spec. Tech found no challenges at todayās visit.
Tech washed and serviced units per service agreement, upon arrival tech could not get to upstairs air handler, would like to reschedule to get upstairs air handler serviced,tech serviced the two condensers and downstairs air handler, both systems are back up and running with a delta t of within spec. Tech found no challenges at todayās visit.
Tech washed and serviced unit per service agreement, upon arrival tech found fuel run capacitor and blower capacitor testing below spec tech recommended replacement of both capacitors customer wants to wait to replace both capacitors, tech also found evaporator coil rusted and corroded tech didnāt pick up on any leaks at todayās visit, system is back up and running with a delta t of 20+ degrees.
Tech washed and serviced unit per service agreement, upon arrival tech found fuel run capacitor and blower capacitor testing below spec tech recommended replacement of both capacitors customer wants to wait to replace both capacitors, tech also found evaporator coil rusted and corroded tech didnāt pick up on any leaks at todayās visit, system is back up and running with a delta t of 20+ degrees.
Tech washed and serviced unit per service agreement, upon arrival tech found fuel run capacitor and blower capacitor testing below spec tech recommended replacement of both capacitors customer wants to wait to replace both capacitors, tech also found evaporator coil rusted and corroded tech didnāt pick up on any leaks at todayās visit, system is back up and running with a delta t of 20+ degrees.
Tech washed and serviced unit per service agreement, upon arrival tech found fuel run capacitor and blower capacitor testing below spec tech recommended replacement of both capacitors customer wants to wait to replace both capacitors, tech also found evaporator coil rusted and corroded tech didnāt pick up on any leaks at todayās visit, system is back up and running with a delta t of 20+ degrees.
PRO VENT INDUSTRIAL MEDIA AIR CLEANER
Tech found ductwork is sweating in a very humid ceiling tile attic space. Insulation is worn and tech recommends replacing ductwork. Tech informed customer that humidity levels are extremely high right now and issue may resolve next week. Customer would like quote from field supervisor.
Tech found ductwork is sweating in a very humid ceiling tile attic space. Insulation is worn and tech recommends replacing ductwork. Tech informed customer that humidity levels are extremely high right now and issue may resolve next week. Customer would like quote from field supervisor.
Tech found ductwork is sweating in a very humid ceiling tile attic space. Insulation is worn and tech recommends replacing ductwork. Tech informed customer that humidity levels are extremely high right now and issue may resolve next week. Customer would like quote from field supervisor.

