Smithfield, NC Plumbing & HVAC Services
Air Conditioning Services That Keep You Cool in Smithfield
Our technicians are trained to handle all types of cooling issues, whether you need a quick repair or a completely new system.
AC Repair
- Diagnose issues like warm air, low airflow, or system failure
- Fix electrical faults, frozen coils, or refrigerant problems
- Fast, same-day service available whenever possible
AC Installation
- Install energy-efficient central air or heat pump systems
- Proper sizing and airflow balancing for optimal performance
- Full walk-through and system training included
Heating Services to Keep You Comfortable
We help you stay warm with reliable service for furnaces and heat pumps throughout the colder months.
Heating Repair
- Identify common problems like no heat, uneven temps, or system cycling
- Service for all brands of furnaces and heat pumps
New Heating Installation
- Replace aging or inefficient systems with modern, energy-saving options
- Expert guidance to find the best solution for your home
Heating & Cooling Maintenance
- Replace Filter / Clean If Permanent
- Disassemble Unit
- Clean Evaporator and Condenser Coils
- Remove All Leaves and Debris
- Tighten All Electrical Connections
- Measure Amp Draws on Compressor, Motors and Heat Strips
- Inspect Outdoor Fan Blade
- Clean and Adjust Blower Wheel if Needed
- Clean and Inspect Flow of Condensate Drain
- Inspect and Test Defrost Cycle
- Inspect Crank Case Heater
- Test Capacitors
- Reassemble Unit, Replace Any Missing or Rusted Screws
- Wash Unit and Apply Protective Coating
- Monitor and Record Delta T
- Inspect Duct System
- Monitor Air Flow
- Inspect Thermostat and Reset to Customer Desire Settings
- Cycle System to Ensure Proper Operation
Full-Service Furnace and Heat Pump Solutions in Smithfield, NC
When winter temperatures drop in Smithfield, your home deserves a heating system you can rely on. At Jackson & Sons, we provide complete furnace and heat pump services tailored to your homeās needs. Whether youāre upgrading an aging system, handling unexpected repairs, or preparing for the season with routine maintenance, our licensed technicians have you covered.
- Install energy-efficient furnaces and heat pumps for consistent winter comfort
- Repair issues like uneven heating, strange smells, or short cycling
- Perform seasonal maintenance to keep your system running safely and efficiently
- Provide expert sizing and system recommendations for new homes or replacements
Stay warm all season long with dependable heating solutions backed by over 50 years of local service.
Indoor Air Quality Products & Services
Clean, healthy indoor air is essential for year-round comfort in Smithfield. At Jackson & Sons, we offer professional indoor air quality services designed to help your family breathe easier. Whether you are battling humidity, allergies, or poor airflow, we can recommend the right solution for your home.
Our indoor air quality services include:
- Installing whole-home air purifiers to remove dust, allergens, and airborne pollutants
- Adding dehumidifiers to control excess moisture and prevent mold growth
- Recommending and installing energy-recovery ventilators for fresh air circulation
- Upgrading HVAC filters and optimizing air handler settings for cleaner airflow
- Conducting air quality assessments to tailor solutions to your homeās needs
Let us help you create a safer, healthier indoor environment in your Smithfield home.
Ductwork Services That Improve Airflow and Comfort
Leaky or poorly designed ductwork can drive up energy bills and leave parts of your home too hot or too cold. At Jackson & Sons, we offer professional ductwork services for homeowners in Smithfield to help restore comfort, improve system performance, and lower utility costs.
- Duct Repair
- Seal and reinforce damaged or disconnected ducts
- Improve airflow to every room in your home
- Duct Replacement
- Remove and replace undersized or failing ductwork
- Install properly insulated, balanced systems for peak efficiency
Plumbing Services for Every Room in the House
Now serving Smithfield with full-service plumbing, Jackson & Sons brings the same trusted care and professionalism our HVAC customers have counted on for decades. Whether youāre dealing with a slow drain, a leaking pipe, or an unexpected plumbing emergency, our licensed plumbers are ready to respond quickly with reliable, long-lasting solutions.
We proudly serve homes throughout Smithfield and nearby Johnston County communities with expert plumbing repairs, installations, and maintenance for kitchens, bathrooms, laundry rooms, and beyond.
Reliable Plumbing Repairs
- Repair leaking faucets, burst pipes, and running toilets
- Fix water pressure issues and damaged valves
- Quick diagnosis with honest recommendations
Drain and Sewer Services
- Clear tough clogs in kitchens, bathrooms, and main lines
- Use professional-grade equipment to remove buildup and debris
- Prevent future blockages and restore normal flow
Water Heater Services
- Repair tank and tankless water heaters
- Resolve no hot water, pilot light issues, or leaking units
- Install efficient models to match your household size and needs
Fixture Upgrades
- Replace outdated faucets, toilets, and showerheads
- Improve water flow, efficiency, and appearance
Emergency Plumbing Help
- Respond to burst pipes, major leaks, and backups
- Stop damage and restore service fast with same-day availability
Why Smithfield Homeowners Trust Jackson & Sons
Weāve served the Smithfield community for generations with reliable HVAC service built on family values, professional workmanship, and local pride. With the addition of our plumbing division, weāre making it even easier to get expert care for your entire home.
- Trusted HVAC provider since 1974
- Now offering licensed plumbing services in Smithfield, NC
- Family-oriented and operated with a focus on quality and integrity
- Same-day service availability whenever possible
- Backed by thousands of 5-star reviewsĀ
When You Need Us, Weāll Be There ā For HVAC and Plumbing in Smithfield, NC
Whether you need furnace repair, AC replacement, or urgent help with a plumbing issue, Jackson & Sons is here with fast, reliable service in Smithfield and nearby communities.
Call (980) 223-0791 or contact us online to schedule your HVAC or plumbing service today. When you need us, weāll be there ā with the comfort and care your home deserves.
Jackson & Sons has completed 25 jobs in Smithfield, NC between January 2025 and February 2025. The 25 customer reviews shown here average 5.0 out of 5. The most recent job was on February 6, 2025. Jackson & Sons has completed 1 job in Smithfield, NC in the last 12 months. The first job there was in August 2016.Recent Jobs and Reviews in Smithfield, NC
Smithfield, NC at a glance
Our Local Reviews by City
Job Locations and Reviews
Upon arrival tech monitored system operation and found suction pressure not dropping in heat mode. Tech did find a low liquid line temp in heat mode, switched to cool mode and found low suction and slightly high head pressure. Warm suction line temp. Added 1.5 lbs of R410A to observe changes, found head pressure rising but suction pressure did not. Confirmed no air flow issues indicating a restriction. No temp difference across filter drier as well as no difference at line temp of liquid line at condenser vs air handler. Indoor TXV is shutting down and will need to be replaced. Screw on valve, photos on file.
- Returned to replace indoor TXV, recovered refrigerant from system and removed filter drier as well as TXV. Brazed in new drier and elbow for screw on TXV at air handler. Pressure tested and evacuated system. Weighed in 8lbs 2oz of R410A per manufacture spec. Added extra 2oz for line set length. System is operating properly.
PERFORMED CMA INSPECTION ON 5 SPLIT SYSTEMS. SPLIT SYSTEM #1 FAN CAPACITOR RATED FOR 20mf TESTED WEAK AT 7.52mf. CAPACITOR DUE FOR FAILURE, RECOMMEND REPLACEMENT OF CAPACITOR. THERE IS AN ESTIMATE ATTACHED TO THIS INVOICE FOR REPLACEMENT OF CAPACITOR. TECH WAS GIVEN APPROVAL BY MR. MCDONALD TO REPLACE 20mf FAN CAPACITOR. SPLIT SYSTEM #4 FAN CAPACITOR RATED FOR 7.5mf TESTED WEAK AT 6.80mf. CAPACITOR DUE FOR FAILURE, RECOMMEND REPLACEMENT OF CAPACITOR. THERE IS AN ESTIMATE ATTACHED TO THIS INVOICE FOR REPLACEMENT OF FAN CAPACITOR. ALL SYSTEMS ARE PERFORMING PROPERLY AT THIS TIME. TECH COMPLETED FILTER CHANGE OF 20-20x20x1 FILTERS. THERE ARE PICTURES AND A PERFORMANCE REPORT ATTACHED TO THIS INVOICE.
Tech arrrived and found thermostat blank, tech found door to air handler had popped off due to stripped out quarter turn locks. Te h taped door shut and power system on. System is now on and operating properly at this time.
Taped up hood connection with water proof white seal tape. Installed blanks in disconnect. Need to return with data plate and possibly one medium sized blank off.
TECH CAME OUT TO FIND BAD SMELL POSSIBLY COMING FROM AIR HANDLER #22 AND CHECK ON UV LIGHT INSIDE SYSTEM. UV LIGHT IS ON INSIDE SYSTEM TECH CLEANED EVAPORATOR COIL AND ADDED CONDENSATE DRAIN TABLETS TO DRAIN PAN. SYSTEM HAD NO STANDING WATER THAT WOULD CAUSE BAD SMELL INSIDE DRAIN PAN AND DRAIN LINES. TECH THROUGHLY CHECKED SYSTEM FOR CAUSE OF SMELL AND DID NOT FIND ANYTHING TO CAUSE BAD SMELL INSIDE SYSTEM. PROBLEM MAY BE RODENT DEAD INSIDE CEILING OR DUCT WORK.
PERFORMED CMA INSPECTION ON 1 PACKAGE HEAT PUMP SYSTEM. TECH FLUSHED DRAIN LINES AND COMPLETED FILTER CHANGE OF 1-20x30x1 FILTER AND 1-14x30x1 FILTER. THERMOSTAT IS OPERATING PROPERLY AND SYSTEM IS COOLING PROPERLY WITH AMDELTA T ABOVE 20 DEGREES. FAN, COMPRESSOR AND BLOWOR MOTOR AMPERAGE ARE INSIDE CORRECT SPECIFICATIONS. THERE ARE PICTURES AND A PERFORMANCE REPORT ATTACHED TO THIS INVOICE.
PERFORMED CMA INSPECTION ON 1 MINI SPLIT SYSTEM. SYSTEM IS PERFORMING PROPERLY AT THIS TIME. FILTERS IN AIR HANDLER ARE CLEAN AND DRAIN LONES ARE CLEAR. SYSTEM SUPPLYING A TEMP OF 46 DEGREES. THERE ARE PICTURES AND A PERFORMANCE REPORT ATTACHED TO THIS INVOICE. .
Open 34 1/2 by 35 tall
50 gallon 240 volts also want estimate on him provide lavatory faucet and use provide
Upon arrival tech was informed that exhaust fan for multiple bathrooms was not pulling air. Inspected fan and found motor to be receiving 120v but was not running. Tested capacitor and it read within specs. Motor for exhaust fan has failed. Customer would like to have a quote to replace just motor as well as replacing entire exhaust.
Tech washed and serviced unit and found no challenges at this time.
Inspected upstairs and downstairs system, determined upstairs system to be issued system. Found missing heat strip kit at air handler in attic, also found removed and blocked return line. Air leaks at attempted seal on return box where return line was previously attached. Other attached existing return is not enough for this 3 ton system. Sent estimate on repairs. Customer will call if decision is made to proceed. Stated electrical will need to be upgraded and completed before heat strips can be added.
Found thermostat for Carrier air handler 3 (serial 4058) not getting power due to flat switch not making connection. Tech reset float switch and ensured wire nuts are solidly connected. Tstat is getting power and system is back running. No charge due to recent CMA.
Tech serviced and cleaned unit. Tech found bacteria build up on blower wheel. Tech pulled and cleaned. Tech also found hard start kit getting close to its threshold rating at 214.8/196. Tech faced no other challenges. Unit is heating and cooling efficiently. Tech informed customer about PSA renewal. Mail invoice.
āPerformed CMA Inspection on 6 Rooftop Package Units, 3 Split Heat Pumps, and 1 Mini Split Heat Pump.
āRTU-5 2015 York Gas Package: East Wing: Compressor tested in bad range on megohm test. This indicates the compressor motor windings insulation has deteriorated, and compressor is due for failure. Evaporator coil and drain pan highly corroded. Due to age of system, condition of evaporator coil, and likelihood of compressor failure, customer should consider system replacement.
āRTU-6 2014 Carrier Gas Package: West Wing: Compressor tested in caution range on megohm test. This indicates the compressor motor windings insulation is deteriorating, and compressor may be due for failure. Outdoor fan motor amperage high. FLA 1.5, actual 1.89. Outdoor fan motor is failing and in need of replacement. 1/4 hp 208/230 1075 rpm. Capacitor included with motor replacement. Provided estimate to replace motor. Due to age of system and cost of recommended repairs, customer should consider options for s
Tech found the managerās office are have 5 zones. Tech turned all thermostats on and found 2 zones not opening. Tech found the lobby area thermostat was set as a conventional and changed to heat pump. That zone is now opening. Tech found the damper we just replaced is not opening. The zone board is receiving the call from the thermostat but is not sending power on open. There are 3 open zones available on the zone boards and tech moved zone 2 on board 1 to zone 2 on board 2 and found damper opening and closing properly. Customer requested checking the gas pressure on the furnace we cleaned the heat exchangers. Tech found 2.48 inlet pressure with LP gas. Inlet pressure should be near 15 outlet should be at least 10. Tech checked the furnace beside this unit and found inlet pressure is also 2.4. Customer is calling the gas company and will call us back to recheck furnaces.
Tech found the managerās office are have 5 zones. Tech turned all thermostats on and found 2 zones not opening. Tech found the lobby area thermostat was set as a conventional and changed to heat pump. That zone is now opening. Tech found the damper we just replaced is not opening. The zone board is receiving the call from the thermostat but is not sending power on open. There are 3 open zones available on the zone boards and tech moved zone 2 on board 1 to zone 2 on board 2 and found damper opening and closing properly. Customer requested checking the gas pressure on the furnace we cleaned the heat exchangers. Tech found 2.48 inlet pressure with LP gas. Inlet pressure should be near 15 outlet should be at least 10. Tech checked the furnace beside this unit and found inlet pressure is also 2.4. Customer is calling the gas company and will call us back to recheck furnaces.
Tech found the managerās office are have 5 zones. Tech turned all thermostats on and found 2 zones not opening. Tech found the lobby area thermostat was set as a conventional and changed to heat pump. That zone is now opening. Tech found the damper we just replaced is not opening. The zone board is receiving the call from the thermostat but is not sending power on open. There are 3 open zones available on the zone boards and tech moved zone 2 on board 1 to zone 2 on board 2 and found damper opening and closing properly. Customer requested checking the gas pressure on the furnace we cleaned the heat exchangers. Tech found 2.48 inlet pressure with LP gas. Inlet pressure should be near 15 outlet should be at least 10. Tech checked the furnace beside this unit and found inlet pressure is also 2.4. Customer is calling the gas company and will call us back to recheck furnaces.
Tech found the managerās office are have 5 zones. Tech turned all thermostats on and found 2 zones not opening. Tech found the lobby area thermostat was set as a conventional and changed to heat pump. That zone is now opening. Tech found the damper we just replaced is not opening. The zone board is receiving the call from the thermostat but is not sending power on open. There are 3 open zones available on the zone boards and tech moved zone 2 on board 1 to zone 2 on board 2 and found damper opening and closing properly. Customer requested checking the gas pressure on the furnace we cleaned the heat exchangers. Tech found 2.48 inlet pressure with LP gas. Inlet pressure should be near 15 outlet should be at least 10. Tech checked the furnace beside this unit and found inlet pressure is also 2.4. Customer is calling the gas company and will call us back to recheck furnaces.
Tech found the managerās office are have 5 zones. Tech turned all thermostats on and found 2 zones not opening. Tech found the lobby area thermostat was set as a conventional and changed to heat pump. That zone is now opening. Tech found the damper we just replaced is not opening. The zone board is receiving the call from the thermostat but is not sending power on open. There are 3 open zones available on the zone boards and tech moved zone 2 on board 1 to zone 2 on board 2 and found damper opening and closing properly. Customer requested checking the gas pressure on the furnace we cleaned the heat exchangers. Tech found 2.48 inlet pressure with LP gas. Inlet pressure should be near 15 outlet should be at least 10. Tech checked the furnace beside this unit and found inlet pressure is also 2.4. Customer is calling the gas company and will call us back to recheck furnaces.
Tech found the managerās office are have 5 zones. Tech turned all thermostats on and found 2 zones not opening. Tech found the lobby area thermostat was set as a conventional and changed to heat pump. That zone is now opening. Tech found the damper we just replaced is not opening. The zone board is receiving the call from the thermostat but is not sending power on open. There are 3 open zones available on the zone boards and tech moved zone 2 on board 1 to zone 2 on board 2 and found damper opening and closing properly. Customer requested checking the gas pressure on the furnace we cleaned the heat exchangers. Tech found 2.48 inlet pressure with LP gas. Inlet pressure should be near 15 outlet should be at least 10. Tech checked the furnace beside this unit and found inlet pressure is also 2.4. Customer is calling the gas company and will call us back to recheck furnaces.
Tech found the managerās office are have 5 zones. Tech turned all thermostats on and found 2 zones not opening. Tech found the lobby area thermostat was set as a conventional and changed to heat pump. That zone is now opening. Tech found the damper we just replaced is not opening. The zone board is receiving the call from the thermostat but is not sending power on open. There are 3 open zones available on the zone boards and tech moved zone 2 on board 1 to zone 2 on board 2 and found damper opening and closing properly. Customer requested checking the gas pressure on the furnace we cleaned the heat exchangers. Tech found 2.48 inlet pressure with LP gas. Inlet pressure should be near 15 outlet should be at least 10. Tech checked the furnace beside this unit and found inlet pressure is also 2.4. Customer is calling the gas company and will call us back to recheck furnaces.
Tech found the managerās office are have 5 zones. Tech turned all thermostats on and found 2 zones not opening. Tech found the lobby area thermostat was set as a conventional and changed to heat pump. That zone is now opening. Tech found the damper we just replaced is not opening. The zone board is receiving the call from the thermostat but is not sending power on open. There are 3 open zones available on the zone boards and tech moved zone 2 on board 1 to zone 2 on board 2 and found damper opening and closing properly. Customer requested checking the gas pressure on the furnace we cleaned the heat exchangers. Tech found 2.48 inlet pressure with LP gas. Inlet pressure should be near 15 outlet should be at least 10. Tech checked the furnace beside this unit and found inlet pressure is also 2.4. Customer is calling the gas company and will call us back to recheck furnaces.
Tech found the managerās office are have 5 zones. Tech turned all thermostats on and found 2 zones not opening. Tech found the lobby area thermostat was set as a conventional and changed to heat pump. That zone is now opening. Tech found the damper we just replaced is not opening. The zone board is receiving the call from the thermostat but is not sending power on open. There are 3 open zones available on the zone boards and tech moved zone 2 on board 1 to zone 2 on board 2 and found damper opening and closing properly. Customer requested checking the gas pressure on the furnace we cleaned the heat exchangers. Tech found 2.48 inlet pressure with LP gas. Inlet pressure should be near 15 outlet should be at least 10. Tech checked the furnace beside this unit and found inlet pressure is also 2.4. Customer is calling the gas company and will call us back to recheck furnaces.
Upon arrival tech found new thermostat wired wrong. Corrected wiring and tested operation, system is back up and heating.
Tech returned to replace Zone 2 damper motor in front office. Replaced and tested, also pulled and cleaned heat exchanger on furnace 8. Heat exchanger was heavily blocked with soot buildup. Reinstalled heat exchanger. Supply gas pressure is too low at 3ā which has caused such heavy buildup with a low output pressure on LP gas. Informed customer of low gas supply issue and they will call gas company. Stated to call once issue is resolved so we can return to adjust gas pressure as well as replace flue piping and confirm proper operation.
Jacksonās and Sons always does an awesome job. Juan was nice, professional, explained upfront what he would be doing, and took the time to answer my questions. Thank you for your wonderful service Juan R.
Very prompt, informed technicians; helpful
Great service from Logan very professional
Noah was awesome! Polite, informative and thorough! Extremely satisfied!
Logan was very nice and explaine what he would be doing while at our house, A super great service guy, Thank again for such great service, I'll give him an A +
Good service
Noah Carter was terrific. He explained what he was going to do and then did a follow up as to what he had done. Noah even showed me pictures of my unit while explaining the work done. Thanks Noah for your wonderful service!
Jackson & Sons has provided us our HVAC needs for many years. Iām very particular and am not easily impressed. On this date (7/16/21), Juan accomplished our annual maintenance on our two systems. He was cordial, knowledgeable, and presented with a high degree of professionalism.
Jason
Excellent service!
Did a good job. Very nice
Wonderful service!
Check up
It would be nice to purchase plans that were longer than a year for a discount.
Technician arrived at the expected time.
Very professional and Courteous
Matthew seems to do a thorough job and communicates well.
Technician was great!
Good service and friendly
The young man was very professional and courteous
Cuyler was punctual, well mannered and did a terrific job on my ac/heat unit in a timely manner. Upon arrival, Cuyler informed me what he would be doing and reviewed what he had done before he left. Thanks Cuyler for a great job!
Pleasant professional informative
Nice people to work with.
Great service, very polite and was honest about work done and possible work needed.
thorough service with evident desire to please the customer .

