Smithfield, NC Plumbing & HVAC Services
Air Conditioning Services That Keep You Cool in Smithfield
Our technicians are trained to handle all types of cooling issues, whether you need a quick repair or a completely new system.
AC Repair
- Diagnose issues like warm air, low airflow, or system failure
- Fix electrical faults, frozen coils, or refrigerant problems
- Fast, same-day service available whenever possible
AC Installation
- Install energy-efficient central air or heat pump systems
- Proper sizing and airflow balancing for optimal performance
- Full walk-through and system training included
Heating Services to Keep You Comfortable
We help you stay warm with reliable service for furnaces and heat pumps throughout the colder months.
Heating Repair
- Identify common problems like no heat, uneven temps, or system cycling
- Service for all brands of furnaces and heat pumps
New Heating Installation
- Replace aging or inefficient systems with modern, energy-saving options
- Expert guidance to find the best solution for your home
Heating & Cooling Maintenance
- Replace Filter / Clean If Permanent
- Disassemble Unit
- Clean Evaporator and Condenser Coils
- Remove All Leaves and Debris
- Tighten All Electrical Connections
- Measure Amp Draws on Compressor, Motors and Heat Strips
- Inspect Outdoor Fan Blade
- Clean and Adjust Blower Wheel if Needed
- Clean and Inspect Flow of Condensate Drain
- Inspect and Test Defrost Cycle
- Inspect Crank Case Heater
- Test Capacitors
- Reassemble Unit, Replace Any Missing or Rusted Screws
- Wash Unit and Apply Protective Coating
- Monitor and Record Delta T
- Inspect Duct System
- Monitor Air Flow
- Inspect Thermostat and Reset to Customer Desire Settings
- Cycle System to Ensure Proper Operation
Full-Service Furnace and Heat Pump Solutions in Smithfield, NC
When winter temperatures drop in Smithfield, your home deserves a heating system you can rely on. At Jackson & Sons, we provide complete furnace and heat pump services tailored to your homeās needs. Whether youāre upgrading an aging system, handling unexpected repairs, or preparing for the season with routine maintenance, our licensed technicians have you covered.
- Install energy-efficient furnaces and heat pumps for consistent winter comfort
- Repair issues like uneven heating, strange smells, or short cycling
- Perform seasonal maintenance to keep your system running safely and efficiently
- Provide expert sizing and system recommendations for new homes or replacements
Stay warm all season long with dependable heating solutions backed by over 50 years of local service.
Indoor Air Quality Products & Services
Clean, healthy indoor air is essential for year-round comfort in Smithfield. At Jackson & Sons, we offer professional indoor air quality services designed to help your family breathe easier. Whether you are battling humidity, allergies, or poor airflow, we can recommend the right solution for your home.
Our indoor air quality services include:
- Installing whole-home air purifiers to remove dust, allergens, and airborne pollutants
- Adding dehumidifiers to control excess moisture and prevent mold growth
- Recommending and installing energy-recovery ventilators for fresh air circulation
- Upgrading HVAC filters and optimizing air handler settings for cleaner airflow
- Conducting air quality assessments to tailor solutions to your homeās needs
Let us help you create a safer, healthier indoor environment in your Smithfield home.
Ductwork Services That Improve Airflow and Comfort
Leaky or poorly designed ductwork can drive up energy bills and leave parts of your home too hot or too cold. At Jackson & Sons, we offer professional ductwork services for homeowners in Smithfield to help restore comfort, improve system performance, and lower utility costs.
- Duct Repair
- Seal and reinforce damaged or disconnected ducts
- Improve airflow to every room in your home
- Duct Replacement
- Remove and replace undersized or failing ductwork
- Install properly insulated, balanced systems for peak efficiency
Plumbing Services for Every Room in the House
Now serving Smithfield with full-service plumbing, Jackson & Sons brings the same trusted care and professionalism our HVAC customers have counted on for decades. Whether youāre dealing with a slow drain, a leaking pipe, or an unexpected plumbing emergency, our licensed plumbers are ready to respond quickly with reliable, long-lasting solutions.
We proudly serve homes throughout Smithfield and nearby Johnston County communities with expert plumbing repairs, installations, and maintenance for kitchens, bathrooms, laundry rooms, and beyond.
Reliable Plumbing Repairs
- Repair leaking faucets, burst pipes, and running toilets
- Fix water pressure issues and damaged valves
- Quick diagnosis with honest recommendations
Drain and Sewer Services
- Clear tough clogs in kitchens, bathrooms, and main lines
- Use professional-grade equipment to remove buildup and debris
- Prevent future blockages and restore normal flow
Water Heater Services
- Repair tank and tankless water heaters
- Resolve no hot water, pilot light issues, or leaking units
- Install efficient models to match your household size and needs
Fixture Upgrades
- Replace outdated faucets, toilets, and showerheads
- Improve water flow, efficiency, and appearance
Emergency Plumbing Help
- Respond to burst pipes, major leaks, and backups
- Stop damage and restore service fast with same-day availability
Why Smithfield Homeowners Trust Jackson & Sons
Weāve served the Smithfield community for generations with reliable HVAC service built on family values, professional workmanship, and local pride. With the addition of our plumbing division, weāre making it even easier to get expert care for your entire home.
- Trusted HVAC provider since 1974
- Now offering licensed plumbing services in Smithfield, NC
- Family-oriented and operated with a focus on quality and integrity
- Same-day service availability whenever possible
- Backed by thousands of 5-star reviewsĀ
When You Need Us, Weāll Be There ā For HVAC and Plumbing in Smithfield, NC
Whether you need furnace repair, AC replacement, or urgent help with a plumbing issue, Jackson & Sons is here with fast, reliable service in Smithfield and nearby communities.
Call (980) 223-0791 or contact us online to schedule your HVAC or plumbing service today. When you need us, weāll be there ā with the comfort and care your home deserves.
Jackson & Sons has completed 25 jobs in Smithfield, NC in July 2024. The most recent job was on July 25, 2024. Jackson & Sons has completed 1 job in Smithfield, NC in the last 12 months. The first job there was in August 2016.Recent Jobs and Reviews in Smithfield, NC
Smithfield, NC at a glance
Our Local Reviews by City
Job Locations and Reviews
Tech repaired leak, replaced filter drier, pressure tested, pulled a vacuum and recharged system. System is now cooling properly. Tech was told by office not to replace condensate pump.
Tech repaired leak, replaced filter drier, pressure tested, pulled a vacuum and recharged system. System is now cooling properly. Tech was told by office not to replace condensate pump.
Tech repaired leak, replaced filter drier, pressure tested, pulled a vacuum and recharged system. System is now cooling properly. Tech was told by office not to replace condensate pump.
Tech repaired leak, replaced filter drier, pressure tested, pulled a vacuum and recharged system. System is now cooling properly. Tech was told by office not to replace condensate pump.
Tech repaired leak, replaced filter drier, pressure tested, pulled a vacuum and recharged system. System is now cooling properly. Tech was told by office not to replace condensate pump.
Tech repaired leak, replaced filter drier, pressure tested, pulled a vacuum and recharged system. System is now cooling properly. Tech was told by office not to replace condensate pump.
Tech repaired leak, replaced filter drier, pressure tested, pulled a vacuum and recharged system. System is now cooling properly. Tech was told by office not to replace condensate pump.
Tech found the carrier unit controls the offices and is controlled by thermostat labeled lobby. Maintenance supervisors office was 80 but sensor is located by the HUB and is temperature being influenced by the HUB thermostat causing that unit to only run 1st stage or not run at all due to being satisfied. 6 degree temperature difference between maintenance office and sensor. Maintenance office is close to the area controlled by the kitchen unit, kitchen unit is down due to low refrigerant. Tech found standing pressure only at 68 psi 410a with 79 degree ambient. Tech found oil and liquid line rubbing against discharge and was able to pinpoint the leak. Once leak is repaired, room temperature difference should level out.
Tech found the carrier unit controls the offices and is controlled by thermostat labeled lobby. Maintenance supervisors office was 80 but sensor is located by the HUB and is temperature being influenced by the HUB thermostat causing that unit to only run 1st stage or not run at all due to being satisfied. 6 degree temperature difference between maintenance office and sensor. Maintenance office is close to the area controlled by the kitchen unit, kitchen unit is down due to low refrigerant. Tech found standing pressure only at 68 psi 410a with 79 degree ambient. Tech found oil and liquid line rubbing against discharge and was able to pinpoint the leak. Once leak is repaired, room temperature difference should level out.
Tech found the carrier unit controls the offices and is controlled by thermostat labeled lobby. Maintenance supervisors office was 80 but sensor is located by the HUB and is temperature being influenced by the HUB thermostat causing that unit to only run 1st stage or not run at all due to being satisfied. 6 degree temperature difference between maintenance office and sensor. Maintenance office is close to the area controlled by the kitchen unit, kitchen unit is down due to low refrigerant. Tech found standing pressure only at 68 psi 410a with 79 degree ambient. Tech found oil and liquid line rubbing against discharge and was able to pinpoint the leak. Once leak is repaired, room temperature difference should level out.
Tech found the carrier unit controls the offices and is controlled by thermostat labeled lobby. Maintenance supervisors office was 80 but sensor is located by the HUB and is temperature being influenced by the HUB thermostat causing that unit to only run 1st stage or not run at all due to being satisfied. 6 degree temperature difference between maintenance office and sensor. Maintenance office is close to the area controlled by the kitchen unit, kitchen unit is down due to low refrigerant. Tech found standing pressure only at 68 psi 410a with 79 degree ambient. Tech found oil and liquid line rubbing against discharge and was able to pinpoint the leak. Once leak is repaired, room temperature difference should level out.
Tech found the carrier unit controls the offices and is controlled by thermostat labeled lobby. Maintenance supervisors office was 80 but sensor is located by the HUB and is temperature being influenced by the HUB thermostat causing that unit to only run 1st stage or not run at all due to being satisfied. 6 degree temperature difference between maintenance office and sensor. Maintenance office is close to the area controlled by the kitchen unit, kitchen unit is down due to low refrigerant. Tech found standing pressure only at 68 psi 410a with 79 degree ambient. Tech found oil and liquid line rubbing against discharge and was able to pinpoint the leak. Once leak is repaired, room temperature difference should level out.
Tech found the carrier unit controls the offices and is controlled by thermostat labeled lobby. Maintenance supervisors office was 80 but sensor is located by the HUB and is temperature being influenced by the HUB thermostat causing that unit to only run 1st stage or not run at all due to being satisfied. 6 degree temperature difference between maintenance office and sensor. Maintenance office is close to the area controlled by the kitchen unit, kitchen unit is down due to low refrigerant. Tech found standing pressure only at 68 psi 410a with 79 degree ambient. Tech found oil and liquid line rubbing against discharge and was able to pinpoint the leak. Once leak is repaired, room temperature difference should level out.
Tech found the carrier unit controls the offices and is controlled by thermostat labeled lobby. Maintenance supervisors office was 80 but sensor is located by the HUB and is temperature being influenced by the HUB thermostat causing that unit to only run 1st stage or not run at all due to being satisfied. 6 degree temperature difference between maintenance office and sensor. Maintenance office is close to the area controlled by the kitchen unit, kitchen unit is down due to low refrigerant. Tech found standing pressure only at 68 psi 410a with 79 degree ambient. Tech found oil and liquid line rubbing against discharge and was able to pinpoint the leak. Once leak is repaired, room temperature difference should level out.
Tech found the carrier unit controls the offices and is controlled by thermostat labeled lobby. Maintenance supervisors office was 80 but sensor is located by the HUB and is temperature being influenced by the HUB thermostat causing that unit to only run 1st stage or not run at all due to being satisfied. 6 degree temperature difference between maintenance office and sensor. Maintenance office is close to the area controlled by the kitchen unit, kitchen unit is down due to low refrigerant. Tech found standing pressure only at 68 psi 410a with 79 degree ambient. Tech found oil and liquid line rubbing against discharge and was able to pinpoint the leak. Once leak is repaired, room temperature difference should level out.
Tech found the carrier unit controls the offices and is controlled by thermostat labeled lobby. Maintenance supervisors office was 80 but sensor is located by the HUB and is temperature being influenced by the HUB thermostat causing that unit to only run 1st stage or not run at all due to being satisfied. 6 degree temperature difference between maintenance office and sensor. Maintenance office is close to the area controlled by the kitchen unit, kitchen unit is down due to low refrigerant. Tech found standing pressure only at 68 psi 410a with 79 degree ambient. Tech found oil and liquid line rubbing against discharge and was able to pinpoint the leak. Once leak is repaired, room temperature difference should level out.
Performed CMA Full Service 1st Visit on 5 Rooftop package Units, 3 Split Heat Pump Systems and 1 Mini Split.
Challenge - RTU - Kitchen 1 - Carrier - upon arrival the system was not operating. Technician replaced the condenser fan motor and was able to get the system up and running. Shortly after, the maintenance staff informed the tech that the system stopped working again. Technician inspected the system and found the blower belt was severely loose. The result was that the system would intermittently switch between circuit 1 and 2, and not efficiently cool the space. Technician tightened down the belt and restored power. Tech was then informed that the system was cooling once again. While finishing up the entire job, the tech was informed again that the system was not cooling. Tech recommends a demand tech to further diagnose challenges with this system.
Challenge - Mini Split - Therapy - the condensate pump needs to be replaced. One currently attached to the system is only interm
Tech washed and serviced unit and found no challenges at this time (unit is 6 months old). There were no recommendations at this time. Unit is up and cooling with a delta t of 25.
Upon arrival customer stated, all 5 units are currently down. Tech found carrier unit for main office compressor #1 cut out on High head pressure due to failed condenser fan motor. Other 3 system need condenser coils cleaned. The last system that faces the road has a blower belt snapped in half, customer has a blower belt for the unit. Tech charged for installation of customer supplied blower belt, that system is back up and cooling. All 5 systems need to be labeled tomorrow morning as well as outdoor fan replacement when CMA scheduled. Customer has to leave, so CMA will need to make repairs. 3 systems are currently down until coil are cleaned.
Performed CMA Full Service on 1 Rooftop Package Unit. No challenges present during todayās visit. The system is cooling properly and holding a delta t of 20 degrees.
Upon arrival customer stated ducts were sweating. After further inspection tech found air vent located right next to fan/hood was sweating not actual duct work. Exhaust fan is pulling coil air across fan/hood cause it to sweat. No issues at todays visit.
Tech found solenoids were opening properly on both circuits. Circuit 1 is shutting down within secs of operating. Tech measured temp difference on the solenoid no temp drop tech found extreme tech deference on the fixed orfice as if restricted. Tech suspected fixed orfice is restricted and causing circuit 1 to shut down tech by passed and is only allowing circuit 2 to run system is cooling at 50 percent capacity.
Techs replaced both cooling solenoid valves, system continued to run high pressure before it shuts down. Discharge solenoid valves are not receiving 24 volts. Techs suspect discharge solenoid valves are malfunctioning and will have to return to further diagnose the system as per office instructions.
Tech preformed CMA FULL SERVICE on 1 Mini Split System. System is operating within specifications at this time and dispensing 49 degree air. Tech removed blower wheel and drain pan and cleaned, then reinstalled. Condensate pump is operating at this time with no clogged. Tech has attached SYSTEM PERFORMANCE REPORT to invoice along with pictures.
Tech performed esa on trane package unit, found no challenges at todays visit.

